Fedora 23 Server - Revision history

Wayne-workman.28155: /* Continue installation */

2016-09-24T13:38:00Z

‎Continue installation

2016-08-09T21:44:43Z

‎Continue pre-config: Update UPD ranges

2016-07-02T23:08:17Z

2016-06-07T22:28:36Z

‎Continue pre-config

2016-06-07T22:26:40Z

‎Continue pre-config

2016-06-07T22:05:33Z

‎Continue pre-config

2016-05-06T12:36:31Z

‎Continue pre-config

2016-04-24T14:42:07Z

‎Setup FOG Trunk

2016-04-24T14:39:13Z

‎Continue pre-config

2016-03-14T23:04:06Z

‎Setup FOG Trunk

@@ Line 34: / Line 34: @@
 == Continue installation ==
-*Under network settings, set a static IP with Subnet & router info and a name. DNS entries are comma delimited (no spaces).
+*Under network settings, set a static IP with Subnet & router info and set a hostname. DNS entries are comma delimited (no spaces). For these to take effect, you can toggle off/on the network adapter. It's a slide switch on the NIC selection page.
 *Set the timezone (and any preferred NTP servers).

@@ Line 65: / Line 65: @@
 for service in http https tftp ftp mysql nfs mountd rpc-bind proxy-dhcp samba; do firewall-cmd --permanent --zone=public --add-service=$service; done
-echo "Open UDP port 9000 and 9001, these are the default ports of udp-sender."
+echo "Open UDP port 49152 through 65532, the possible used ports for fog multicast"
-firewall-cmd --permanent --add-port=9000-9001/udp
+firewall-cmd --permanent --add-port=49152-65532/udp
 echo "Allow IGMP traffic for multicast"
 firewall-cmd --permanent --direct --add-rule ipv4 filter INPUT 0 -p igmp -j ACCEPT

← Older revision		Revision as of 23:08, 2 July 2016
Line 122:		Line 122:
	== Set the FOG services to start 30 seconds after boot ==		== Set the FOG services to start 30 seconds after boot ==

−	Necessary with Fedora 23 & r6551 and above (FOG 1.3.0 is above r6551). There's an issue with the FOGMulticastManager after a reboot; it's timing related. There are also steps included to delay NFS and RPC for 30 seconds as well, this is needed for very fast servers - doing it on all servers won't hurt.	+	Necessary with Fedora 23 & r6551 and above (FOG 1.3.0 is above r6551). There can be an issue with the FOGMulticastManager after a reboot; it's timing related. There are also steps included to delay NFS and RPC for 30 seconds as well, this is needed for very fast servers - doing it on all servers won't hurt.

@@ Line 67: / Line 67: @@
 echo "Open UDP port 9000 and 9001, these are the default ports of udp-sender."
 firewall-cmd --permanent --add-port=9000-9001/udp
-echo "Allow ICMP traffic for multicast"
+echo "Allow IGMP traffic for multicast"
 firewall-cmd --permanent --direct --add-rule ipv4 filter INPUT 0 -p igmp -j ACCEPT
 systemctl restart firewalld.service

@@ Line 65: / Line 65: @@
 for service in http https tftp ftp mysql nfs mountd rpc-bind proxy-dhcp samba; do firewall-cmd --permanent --zone=public --add-service=$service; done
-echo "Open UDP port 9000, this is the default port of udp-sender."
+echo "Open UDP port 9000 and 9001, these are the default ports of udp-sender."
-firewall-cmd --permanent --add-port=9000/udp
+firewall-cmd --permanent --add-port=9000-9001/udp
 echo "Allow ICMP traffic for multicast"
 firewall-cmd --permanent --direct --add-rule ipv4 filter INPUT 0 -p igmp -j ACCEPT

@@ Line 64: / Line 64: @@
 systemctl enable firewalld
 for service in http https tftp ftp mysql nfs mountd rpc-bind proxy-dhcp samba; do firewall-cmd --permanent --zone=public --add-service=$service; done
-firewall-cmd --permanent --direct --add-rule ipv4 filter INPUT 0 -m udp -p udp -m pkttype --pkt-type multicast -j ACCEPT
 systemctl restart firewalld.service
-echo Initial firewalld config done.
+echo "Done."
 </pre>

@@ Line 107: / Line 107: @@
 git clone --depth 1 https://github.com/FOGProject/fogproject.git
 cd fogproject/bin
-./installfog.sh</pre>
+./installfog.sh
 *Follow the on-screen instructions to setup fog for your environment. If you are unsure about anything, choose the default option.

@@ Line 93: / Line 93: @@
 = Setup FOG Trunk =
-This will install the latest developmental version of FOG using the Subversion method found here: [[Upgrade to trunk]]
+This will install the latest developmental version of FOG using the Git method found here: [[Upgrade to trunk]]
 We need to use FOG Trunk with Fedora 23 and later because the latest stable release of FOG (currently 1.2.0) does not support any recent versions of Fedora.