Difference between revisions of "Tftp timeout"

From FOG Project
Jump to: navigation, search
m (Other Troubleshooting)
 
(6 intermediate revisions by the same user not shown)
Line 35: Line 35:
 
</pre>
 
</pre>
  
== Other Troubleshooting ==
+
= Other Troubleshooting =
 
=== 0.32 and below ===
 
=== 0.32 and below ===
 
*From your FOG server test out tftp
 
*From your FOG server test out tftp
Line 59: Line 59:
 
  tftp x.x.x.x get undionly.kpxe
 
  tftp x.x.x.x get undionly.kpxe
 
</pre>
 
</pre>
 
----
 
 
  
 
====Expected Results====
 
====Expected Results====
Line 69: Line 66:
 
</pre>
 
</pre>
  
 
+
<hr>
'''----'''
 
  
 
=Restart TFTP Service=
 
=Restart TFTP Service=
Line 78: Line 74:
 
</pre>
 
</pre>
  
 +
<hr>
  
'''----'''
+
=Rights to tftpboot folder=
 +
* Are the rights to your tftpboot folder correct?
 +
** If you tried the above [[Section-1.5.2]] and you get the "Expected results" then the rights are correct.
  
 +
<hr>
  
 
=Check DHCP Option 67=
 
=Check DHCP Option 67=
 
* Go to your DHCP and confirm that option 67 is set to undionly.kpxe.
 
* Go to your DHCP and confirm that option 67 is set to undionly.kpxe.
 
+
**{{:DHCP_Settings}}
 
 
'''----'''
 
 
 
=Rights to tftpboot folder=
 
* Are the rights to your tftpboot folder correct?
 
** If you tried the above Section-1.5.2 and you get the "Expected results" then the rights are correct.
 

Latest revision as of 14:39, 10 February 2015

If you get this issue its usually due to a firewall issue, do the following:

Disable firwall

Fedora 9

service iptables stop 
service ip6tables stop 
 
chkconfig iptables off 
chkconfig ip6tables off

Fedora 16

Add /bin/bash to /etc/shells as the vsftpd yum install does not do it correctly causing tftp timeout message

Ubuntu

sudo ufw disable

Debian

iptables -F
iptables -X
iptables -t nat -F
iptables -t nat -X
iptables -t mangle -F
iptables -t mangle -X
iptables -P INPUT ACCEPT
iptables -P OUTPUT ACCEPT
iptables -P FORWARD ACCEPT

Other Troubleshooting

0.32 and below

  • From your FOG server test out tftp
tftp -v X.X.X.X -c get pxelinux.0
  • From a Windows PC run at the cmd prompt: (Windows TFTP Service must be Installed first)
 tftp x.x.x.x get pxelinux.0

0.33 and 1.x.x

  • From your FOG server test out tftp
tftp -v X.X.X.X -c get undionly.kpxe
  • From a Windows PC run at the cmd prompt: (Windows TFTP Service must be Installed first)
 tftp x.x.x.x get undionly.kpxe

Expected Results

  • If tftp & xinetd are running your should get:
Received XXXX bytes in X.X seconds....

Restart TFTP Service

  • Restart the TFTP service.
service tftpd-hpa restart

Rights to tftpboot folder

  • Are the rights to your tftpboot folder correct?
    • If you tried the above Section-1.5.2 and you get the "Expected results" then the rights are correct.

Check DHCP Option 67

  • Go to your DHCP and confirm that option 67 is set to undionly.kpxe.
    • ==DHCP Settings==
  • It is important to know that versions 0.32 and below use pxelinux.0 for option 67 in DHCP
  • For all versions 0.33 to current(1.3.0beta) use undionly.kpxe is generally recommended for option 67.
    • Other files that can be used are listed in your directory "/tftpboot"

Linux Based (ISC-DHCP)

Articles related to ISC-DHCP

BIOS and UEFI Co-Existence

ProxyDHCP with dnsmasq

FOG on a MAC

Fedora 21 Server#Verify Fedora DHCP config (if_using_DHCP)

Start/stop/enable/disable

Configure DHCP

FOG dnsmasq (ProxyDHCP)

  • You would use ProxyDHCP if you do not have access to your DHCP server, or are using a device that isn't capable of specifying option 066 and 067 (next server and file name). The most popular ProxyDHCP method with fog is dnsmasq. This article will walk you through that:
  • Not required unless you have an unmodifiable DHCP server/

Using_FOG_with_an_unmodifiable_DHCP_server/_Using_FOG_with_no_DHCP_server

Non-Linux DHCP

If you do not use FOG to provide DHCP services, the following sections will give some indication of settings for DHCP servers on various platforms.

Windows Server DHCP

  • Option 66
    • Windows 66.png
  • Option 67
    • Windows 67.png


Novell (Linux) Server DHCP

  • DHCP Overview from DNS/DHCP Console (Netware 6.5)
    • Novelldhcp.gif
  • Option 66
    • Novelloption66.gif
  • Option 67
    • Novelloption67.gif

Here is a link from Novell's website on how to setup their DHCP server: http://www.novell.com/coolsolutions/feature/17719.html

MAC Server DHCP

Use OS X Server app to install and utilize DHCP.

Use DHCP Option Code Utility to generate the code necessary.
https://docs.google.com/uc?id=0BwD4il5Z1G6fTmFFYU91bDNuRmc&export=download

One MUST generate the codes in order for PXE booting to work!
bootpd.plist is located in /etc/bootpd.plist

  • Option 66
    • MACOption66.png
  • Option 67
    • MACOption67.png


  • Sample bootpd.plist
    • This is a sample file DO NOT USE THIS IN YOUR ENVIRONMENT!!!! OS X Server app will generate most of this code for you, this example file is to show you the place where the generated code needs to be placed.
    • For Reference, your generated code should be placed between "dhcp_domain_search" and "dhcp_router"


  • Completed Bootpd.plist
    • MACbootpd.png

Other DHCP Configurations

Other DHCP Configurations