Difference between revisions of "Change FOG Server IP Address"

From FOG Project
Jump to: navigation, search
m (Change FOG server settings)
(FOG 1.3.0: Added locations for settings.)
Line 7: Line 7:
 
* Update the settings in the /opt/fog/.fogsettings
 
* Update the settings in the /opt/fog/.fogsettings
 
* Rerun the installer
 
* Rerun the installer
* Update the IP address for the storage node on the FOG system where you changed the IP address
+
* Update the IP address for the storage node on the FOG system where you changed the IP address (`Web Interface -> Storage Management`)
* Update the IP address on a any master storage node that may reference this FOG server
+
* Update the IP address on a any master storage node that may reference this FOG server (`Web Interface -> Storage Management`)
* Update the FOG_WEB_HOST value
+
* Update the FOG_WEB_HOST value (`Web Interface -> FOG Configuration -> FOG Settings -> Web Server -> FOG_WEB_HOST`)
* Update the FOG_TFTP_HOST value
+
* Update the FOG_TFTP_HOST value (`Web Interface -> FOG Configuration -> FOG Settings -> TFTP Server -> FOG_TFTP_HOST`)
  
 
=== FOG Settings File ===
 
=== FOG Settings File ===

Revision as of 16:11, 9 October 2016

Change FOG server static IP address

FOG 1.3.0

Procedural Steps:

  • Update the settings in the /opt/fog/.fogsettings
  • Rerun the installer
  • Update the IP address for the storage node on the FOG system where you changed the IP address (`Web Interface -> Storage Management`)
  • Update the IP address on a any master storage node that may reference this FOG server (`Web Interface -> Storage Management`)
  • Update the FOG_WEB_HOST value (`Web Interface -> FOG Configuration -> FOG Settings -> Web Server -> FOG_WEB_HOST`)
  • Update the FOG_TFTP_HOST value (`Web Interface -> FOG Configuration -> FOG Settings -> TFTP Server -> FOG_TFTP_HOST`)

FOG Settings File

Update the /opt/fog/.fogsettings file:

vi /opt/fog/.fogsettings

Instructions on using Vi: Vi

There are several settings in here that may need updated depending on if you're running DHCP on the fog server or not. But the one setitng that must be updated is the ipaddress=x.x.x.x setting. Update this with the correct IP. Save your changes and quit, and then re-run the fog installer.

Older instructions

FOG server setup

  • Fedora 10
  • SVN of version 0.27
  • IP address:192.168.1.200 (using network manager)
  • Change computer IP address from 192.168.1.200 to 192.168.1.50

Change FOG server settings

  • Cancel any pending capture/deploy tasks Tasks > Active Tasks (Previous IP settings are embedded in task info)
  • Log in to FOG WebUI > about > FOG Settings
    • General Setting: FOG_WOL_HOST
    • TFTP Server: FOG_TFTP_HOST, FOG_PXE_IMAGE_DNSADDRESS
    • WEB Server: FOG_WEB_HOST
  • FOG WebUI > about > PXE Boot Menu > Save PXE Menu
  • FOG WebUI > Storage Management > All Storage Nodes
    • DefaultMember: IP Address
  • DHCP server configuration file (/etc/dhcpd.conf) restart service after changes are made.
    • Next-server 192.168.1.50
  • PXE Menu changes ( /tftpboot/pxelinux.cfg/default)
    • Replace any previous IP addresses with new IP address
    • This also applies if your DNS server has changed. You would replace all previous DNS IP addresses with new DNS server IP address.
    • Example (no change to DNS):
      • Old line in /tftpboot/pxelinux.cfg/default:
        • append initrd=fog/images/init.gz root=/dev/ram0 rw ramdisk_size=127000 ip=dhcp dns=192.168.1.1 mode=quickimage keymap= web=192.168.1.200/fog/ loglevel=4 consoleblank=0
      • New line in /tftpboot/pxelinux.cfg/default:
        • append initrd=fog/images/init.gz root=/dev/ram0 rw ramdisk_size=127000 ip=dhcp dns=192.168.1.1 mode=quickimage keymap= web=192.168.1.50/fog/ loglevel=4 consoleblank=0