Difference between revisions of "Fedora 25 Server"

From FOG Project
Jump to: navigation, search
(Created page with " = Installing Fedora 25 server = == Configuring partitions for FOG == The one thing with using Fedora (or any red-hat based distro) is that the default partitioning isn't op...")
 
 
(One intermediate revision by the same user not shown)
Line 26: Line 26:
 
External Video Link:
 
External Video Link:
  
Video pending...
+
[https://youtu.be/JkapIh1XdjQ  Fedora 25 Optimal FOG Partitioning]
  
 
Video:
 
Video:
  
Video pending...
+
<embedvideo service="youtube">https://www.youtube.com/watch?v=JkapIh1XdjQ&feature=youtu.be</embedvideo>
  
 
== Continue installation ==
 
== Continue installation ==

Latest revision as of 00:26, 7 June 2017

Installing Fedora 25 server

Configuring partitions for FOG

The one thing with using Fedora (or any red-hat based distro) is that the default partitioning isn't optimal for FOG. The default is that "root" only gets 50 GiB and the rest goes to /home. This is not optimal.

You should delete any existing partitions, and then select "create partitions automatically". This is the easiest. Then you can manipulate and delete unneeded partitions. The most simple partitioning setup for FOG is below:

  • Give the swap partition the same amount as the amount of RAM the system has.
  • Optionally delete the /home partition or limit it's size to something very small (perhaps 10GB).
  • Limit / (root) to 20GB instead of 50 (optional but recommended). Please keep in mind that this is also the partition where the snapins are stored. If you plan to use a lot of snapins and don't think that (roughly) 15GB is enough, then leave this at 50.
  • Increase the size of /boot from 500MB to 1GB for breathing room in the future (optional but recommended).
  • Finally, create a /images partition with all remaining space.

Fedora (and most Red-Hat based distributions) auto-adjust partition sizes for you if you go over what is available... meaning.. if you are unsure about how much space is left on the drive to assign to /images, you can leave the size field blank and hit "update" and the installer will auto adjust to what is available.

Another thing to keep in mind is when you install on UEFI enabled hardware, there will be an EFI boot partition made automatically - leave that partition alone.

(Note: Video plays in Chrome or Firefox with html5 plugin)

External Video Link:

Fedora 25 Optimal FOG Partitioning

Video:

Continue installation

  • Under network settings, set a static IP with Subnet & router info and set a hostname. DNS entries are comma delimited (no spaces). For these to take effect, you can toggle off/on the network adapter. It's a slide switch on the NIC selection page.
  • Set the timezone (and any preferred NTP servers).
  • Start installing.
  • Set a root password.

Fedora 25 server pre-config

Update Fedora 25 server

Update everything installed with this line:

dnf update -y

Continue pre-config

After installation is complete and reboot is done, you can work through putty from this point forward. You can get a copy here.

  • Log in as root with the password you set earlier.
  • Configure firewalld:
dnf install firewalld -y
systemctl start firewalld
systemctl enable firewalld
for service in http https tftp ftp mysql nfs mountd rpc-bind proxy-dhcp samba; do firewall-cmd --permanent --zone=public --add-service=$service; done

echo "Open UDP port 49152 through 65532, the possible used ports for fog multicast" 
firewall-cmd --permanent --add-port=49152-65532/udp
echo "Allow IGMP traffic for multicast"
firewall-cmd --permanent --direct --add-rule ipv4 filter INPUT 0 -p igmp -j ACCEPT
systemctl restart firewalld.service
echo "Done."


  • Add firewalld exceptions for DHCP and DNS (if you plan to run DHCP on your FOG server):
for service in dhcp dns; do firewall-cmd --permanent --zone=public --add-service=$service; done
firewall-cmd --reload
echo Additional firewalld config done.


  • Set SELinux to permissive on boot:
sed -i.bak 's/^.*\SELINUX=enforcing\b.*$/SELINUX=permissive/' /etc/selinux/config


  • Set SELinux to permissive on the fly (this is not persistent, the above config must be done to be persistent):
setenforce 0

Setup FOG

We need to use FOG 1.4.2 or later with Fedora 25 and later, as this is currently the latest stable release and is tested working with the latest stable release daily.

dnf install git -y
cd ~
mkdir git
cd git
git clone https://github.com/FOGProject/fogproject.git
cd fogproject/bin
./installfog.sh
echo Now you should have fog installed.
  • Follow the on-screen instructions to setup fog for your environment. If you are unsure about anything, choose the default option.