Search results

Jump to: navigation, search
  • You are now ready to test and deploy your snapin.
    2 KB (422 words) - 17:14, 16 January 2011
  • • PXE-E61: Media test failed, check cable. Most likely the cable is not plugged in or connected.
    14 KB (2,245 words) - 17:50, 29 June 2009
  • You will then be prompted if you would like to test the installation media, choose: '''Skip''' and press enter. ...installation you can start the installation process over and run the media test to check for a bad burn.
    10 KB (1,613 words) - 23:07, 7 April 2011
  • * Added Disk Surface test.
    16 KB (2,236 words) - 03:47, 8 July 2016
  • * PXE boot a computer and test it out! =)
    2 KB (314 words) - 18:00, 10 October 2009
  • === Building a test module === ...ument being the message you want to log. The entry is written to a simple test file typically located at c:\fog.log.
    10 KB (1,340 words) - 12:44, 10 May 2010
  • ...S with multiple partition - error cannot have partition outside disk (will test again w/o system partition)
    2 KB (266 words) - 21:26, 27 December 2011
  • # And, you're done! Try booting a client with your new kernel to test it. Repeat steps 5-7 above if you need to make any changes. If you are happ Test
    3 KB (489 words) - 20:05, 27 August 2019
  • ...2 VMs. One is the FOG server VM, the other is a test PXE client VM used to test out the server. They are connected via an internal virtual network.
    496 bytes (80 words) - 01:45, 25 March 2011
  • ...y Test<br>Wake Up<br>Fast Wipe<br>Normal Wipe<br>Full Wipe<br>Disk Surface Test<br>File Recovery<br>Virus Scan<br>Hardware Inventory
    20 KB (3,142 words) - 03:57, 8 July 2016
  • ...d the [http://en.wikipedia.org/wiki/EICAR_test_file Eicar Test Virus] to a test workstation and run the clam task on that system. Once the scan has finish
    3 KB (572 words) - 12:24, 12 December 2014
  • ...vers in the above list are working in the reseal process. However I cannot test all of them in deployment process because I don't have a motherboard with e
    24 KB (3,764 words) - 01:11, 6 March 2012
  • At this point, you should be done. Test it out. Do be aware that the initrd.gz will take about a minute to load (on
    2 KB (349 words) - 14:14, 8 November 2010
  • And that's it! Go ahead and test out your fancy new PXE server.<br>
    7 KB (1,110 words) - 17:36, 16 December 2016
  • Can be used as kind of a lightweight desktop virtual environment to test FOG and master your images. Using this on the laptop as local test environment. Search forums and wiki but there is no valuable information ab
    11 KB (1,694 words) - 12:23, 19 May 2021
  • *Memory Test *Test Disk
    57 KB (9,737 words) - 13:13, 30 March 2023
  • *Create a test file with some data in it to send later. <pre>[administrator@D620 ~]$ echo 'some text here to send later' > test.txt
    17 KB (2,614 words) - 17:03, 17 August 2016
  • [http://www.topspeedscan.com computer speed test]
    177 bytes (26 words) - 05:43, 16 May 2011
  • // Example: Test by changing all hostnames in Host Management
    15 KB (1,679 words) - 22:41, 2 October 2011
  • |G2=db-test
    11 KB (1,660 words) - 21:43, 28 September 2011

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)